Rev-a-shelf 5190-15RM-111 Manuel d'utilisateur télécharger pdf

1) Pre-drill mounting holes in the locations marked on this Template using a 3/32” drill bit. Be sure the template is centered left to right. The

front edge of the template should be aligned with the back of the door.

2) Use the #8 x ¾” Phillips head screws provided to secure the unit to the oor. The slide system can be separated if necessary to aid in instal-

lation, but removal is not required. (See FIG 1 and FIG 2)

3) Ensure that the door mounting brackets allow the mounting screws to engage a part of the door that is at least 3/4” thick. (On a 5-panel

door, this would be the outer side pieces, or styles) Inset doors would move the brackets toward the center of the unit while full overlay doors

would require the brackets to move outward. (See FIG 3) Use the double sided tape provided to temporarily attach the door to the mounting

brackets.

4) Carefully open the unit, being sure not to disengage the double sided tape. Once the unit is open, use the #6 x ½” at head screws to per-

manently attach the door to the unit. All (8) screws must be used for proper function. Space screws at opposing corners as much as possible.

Door Adjustment

Vertical mounting slots have been used in the bracket that attaches directly to the door. Use these slots for vertical adjustment. (See FIG 4)

Horizontal adjustment is achieved by loosening all 4 of the 3/8” nuts that connect the two brackets and moving the door left to right as needed.

(See FIG 4)

For door tilt adjustment, loosen the 4 #3 phillips head screws below the skirt and adjust. The rear screws are slotted to allow the door to pivot at

the front of the bracket. (See FIG 5)

Keeping the front screws “snug” will aid in adjustment.

T-5190-0114 Series Cloth Hamper

Installation Template

Recommended Screw and Pilot

Hole Location (4) Places

T-5190-0114-TRI

PARTS LIST:

PULLOUT CHASSIS

HAMPER CONTAINER CHASSIS

HAMPER CONTAINERS

8 #6 X 1/2” FLAT HEAD SCREWS

5 #8 X 3/4” PAN HEAD SCREW

DOUBLE SIDED TAPE

TOOLS REQUIRED:

ESTIMATED ASSEMBLY

TIME:

20 MIN

CARE AND MAINTENANCE:

CLEAN WITH A DAMP CLOTH

AND WIPE PARTS DRY

3/32”

Fig 1

Many of our products feature installation videos. Visit Rev-A-Shelf.com for more details.

Front edge of paper

to back of door.

Center of Cabinet

Fig 4

Fig 5

Fig 2

Fig 3

Rotate metal retainer clip and slide clip out to pop

spring o of ball-stud.

Press release lever behind side skirt on each side by

sliding up or down depending on which side. Unit

will seperate with both levers disengaged.

Door thickness must be at least 3/4” where

screws attach

Mounting screws must engage 3/4” thick

material minimum.

Adjust bracket left to right before

attaching door with double-sided tape.

For horizontal adjustment loosen

4 3/8” nuts and move to desired

position

Use vertical slots for

vertical door adjustment

Door tilt adjustment screws

Front of Unit

1 2

Résumé du contenu

Page 1 - Installation Template

1) Pre-drill mounting holes in the locations marked on this Template using a 3/32” drill bit. Be sure the template is centered left to right. The fr

Page 2 - Centre de l’armoire

Plantilla para la Instalación de Contenedores de Basura de las Series canastilla para ropaNotice de montage SERIE T-5190-0114 Panier à linge4 lugares

Modèles reliés 5190-15RM-117

Commentaires sur ces manuels

Pas de commentaire

Rev-a-shelf 5190-15RM-111 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Rev-a-shelf 5190-15RM-111. Rev-A-Shelf 5190-15RM-111 User Manual [cs] [de] [pl] [en] Manuel d'utilisatio

Résumé du contenu

Modèles reliés 5190-15RM-117

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Rev-a-shelf 5190-15RM-111