Rev-a-shelf 4WCTM-RM-2150DM-2 Manuel d'utilisateur télécharger pdf

 





17-15/16” (50 qt.)

12-7/8” (35 qt.)

Face Frame Cabinet Installation

Step 1A Preparing the Unit for installation

Remove the Gas Spring from the unit.

This is done by removing the two retainer clips from each of the ball sockets and then

popping the spring ends from the ball studs. (SEE FIGURE 1A)

Disengage the cabinet members from the unit by pressing the release levers on the 2

slides and pulling them away from the product members. (SEE FIGURE 1A)

Step 2A Attaching Rear Mounting Strap

Fasten the rear strap assembly to the rear cabinet wall using the (4) #8 x 5/8” pan head

screws provided. The CENTER slot of each rear socket should be positioned 17-15/16”

(for 50 qt. frames) or 12-7/8” (for 35 qt. frames) from the oor of the cabinet as shown

in FIGURE 2A. It is best to start with two screws in the center slots in case adjustments

are necessary. Make sure to center the strap assembly left to right according to the

opening of the face frame. (SEE FIG 2A)

Note: If rear of cabinet is thinner than ½”, a furring strip should be used between the

back wall and the mounting strap to ensure the rear mounting strap is properly attached.

Keep in mind the minimum depth required is 21-3/4” and is measured from the back

of the door.

Step 3A Assembling Side Mounting Brackets

For face frame applications, only the product member bracket and the side

mounting bracket are necessary. (SEE FIGURE 3A)

Please refer to Table A for the proper hole alignment. If the table does not

apply to the cabinet in use, the outer slots will provide a fully adjustable

option to t virtually any opening. Fasten the brackets according to table A

using the M5 nuts, bolts, and washers provided.

Step 4A Attaching Slides to Cabinet

While supporting the front of the side mounting bracket engage the back of the slide

with the rear strap assembly by sliding it into the outer socket of the assembly. The

product member should be pushed into the rear strap assembly until the front of each

product member and each side-mounting bracket is ush with the front of the face

frame. This is a press t and there will be resistance. (SEE FIGURE 4A)

Continue to support the front of the slide. Do not let it fall as it may damage the rear

strap assembly.

Locate the bottom of the side-mounting bracket 15 ¾” (for 50 qt. frames) or 10-11/16”

(for 35 qt. frames) from the oor of the cabinet. Attach each bracket to the inside of

the face frame using the (3) #6 x 5/8” at head screws provided. (SEE FIGURE 5A)

Note: it is recommended to pre-drill using a 3/32” drill bit

PROCEED TO STEP 6

FIGURE 2A

FIGURE 5A

CABINET MEMBER

HOLE LOCATION

PRODUCT MEMBER

HOLE LOCATION

MENDING PLATE

HOLE LOCATION

CABINET MEMBER

HOLE LOCATION

PRODUCT MEMBER

HOLE LOCATION

MENDING PLATE

HOLE LOCATION

1.5" Face Frame

N/A

1.625" Face Frame

N/A

1.75" Face Frame

N/A

Frameless with .75" Wall

2 & 5

Frameless with .708" Wall

1 & 8

Frameless with .625" Wall

3 & 6

Shimmed Inset Door 1.5" FF

N/A

Shimmed Inset Door 1.625" FF

N/A

Shimmed Inset Door 1.75" FF

N/A

FIGURE 1A

FIGURE 4A

1-1/2” Face Frame Example

-Product Member Top

-Side Mount Brkt Bottom

INSTALLATION INSTRUCTIONS

For Full Height Top Mount Waste Containers

With Rev-A-Motion

For face frame style cabinets see steps 1A-4A

For frameless style cabinets see steps 1B-5B

For cabinets with inset doors see steps 1C-4C

1 2 3 4

Résumé du contenu

Page 1 - With Rev-A-Motion

 17-15/16” (50 qt.)12-7/8” (35 qt.)Face Frame Cabinet InstallationStep 1A Preparing the Un

Page 2 - .75” Wall Example

Frameless Cabinet InstallationStep 1B Installing Side Mounting Brackets Locate the bottom of the side mounting bracket 15-3/4” (for 50 qt. frames)

Page 3

Inset Door Application Installation Note: Requires ½” minimum wall thicknessStep 1CLocate the bottom of the side mounting bracket 15-3/4” (for 50

Page 4 - I-WCTMSC-0115

Step 6Re-engage the unit into each of the cabinet members being sure that the slides are aligned properly. Once engaged fully close and open the unit

Modèles reliés 4WCTM-RM-2135DM-2

Commentaires sur ces manuels

Pas de commentaire

Rev-a-shelf 4WCTM-RM-2150DM-2 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Rev-a-shelf 4WCTM-RM-2150DM-2. Rev-A-Shelf 4WCTM-RM-2150DM-2 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 4WCTM-RM-2135DM-2

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Rev-a-shelf 4WCTM-RM-2150DM-2